Agilent HP 86100C Wideband Multifunction Oscilloscope Used Refurb Agilent HP 86100C Wideband Multifunction Oscilloscope [86100C] : NSCA, New, Used, and Refurbished Test Equipment for Rent, Lease, or Sale

Categories

Featured Products ...

Manufacturers

Agilent HP 86100C Wideband Multifunction Oscilloscope

AGILENT 86100 WIDEBAND OSCILLOSCOPE (COMMUNICATION ANALYZER)

Agilent 86100 Wideband Oscilloscope (Communication Analyzer)

General Description:

NSCA is proud to offer Agilent’s 86100C, as a used refurbished instrument, complete with warranty and Calibration to Full OEM specification. This instrument is a comprehensive multi-function communication analyzer for high-speed electrical and optical signals.

Agilent’s 86100C Infiniium DCA-J combines high accuracy and repeatability with ease of use to simplify characterizing signals from 50 MHz to 80GHz. Digital designers can combine the mainframe and modules into four key instruments with high signal integrity performance, including:

Ø A Full Function Oscilloscope to 80GHz

Ø A Digital Communications Analyzer

Ø Jitter and Interface Analyzer

Ø A Full Function TDR

Advanced Analysis Features:

Advanced Jitter Analysis

Ø Decomposition of jitter into Total Jitter (TJ), Random Jitter (RJ), Deterministic Jitter (DJ), Periodic Jitter (PJ), Data Dependent Jitter (DDJ), Duty Cycle Distortion (DCD), and Jitter induced by Intersymbol Interference (ISI)

Ø Jitter frequency spectrum

Ø Isolation and analysis of Sub-Rate Jitter (SRJ), that is, periodic jitter that is at an integer sub-rate of the bitrate

Ø Jitter spectrum/phase noise for both clock or data signals (requires 83496B Clock Recovery)

Ø Decomposition of interference into Total Interference (TI), Random Noise (RN), Deterministic Interference, Periodic Interference (PI), and Inter-symbol Interference (ISI)

Advanced Amplitude Analysis

Ø Tabular and graphical results for both one and zero levels

Ø Interference frequency spectrum

Ø Q-factor (isolated from deterministic interference)

Ø Relative Intensity Noise (RIN 1 Level, RIN OMA)

Advanced Waveform Analysis

Ø Accurately capture long waveforms (up to 223 bits) with or without averaging

Ø Samples/waveform limited only by size of hard disk or memory stick

Ø Oscilloscope measurements on equalized waveforms with built-in Linear Feedforward Equalization (LFE) tool

Ø MATLAB® (a registered trademark of The Mathworks Inc) interface allows instant processing of oscilloscope data:

Ø Observe and characterize the output waveforms of any LFE, Decision Feedback Equalizer (DFE) or other algorithm

Ø Calculate and display figures of merit or penalty using proprietary or published scripts, such as Transmitter Waveform Dispersion Penalty (TWDP)

Advanced TDR Analysis (Frequency-Domain S-Parameters)

Ø On-board S-parameters for differential or single-ended characterization

Ø One port or two port devices (single-ended or differential)

Ø Measure to current and new standards

Product Specification/Details:

86100C DCA-J - Oscilloscope Mode

Ø Electrical bandwidth from 12 to over 80 GHz ensure the most precise waveforms and pulse fidelity.

Ø Probing - if connectorized test points are not available, use the Infiniimax probes to your advantage by pairing them with the N1022A probe adapter and the DCA-J's wide bandwidth inputs.

Ø Pattern Lock enables single-valued waveform viewing at even the fastest bit rates when no separate pattern or frame trigger is available.

Ø Even closed eyes can be captured as pulse train data and the effectiveness of common equalization schemes are seen from on-board algorithms.

86100C DCA-J - Eye/Mask Mode

A digital communications analyzer with automated eye diagram analysis for transmitter compliance testing.

Eye diagram analysis is the easiest and most intuitive method for viewing high-speed digital communications waveforms. The 86100C has the capability to view both optical and electrical digital communications signals.

Ø Built-in industry standard optical reference receivers for rates from 155 Mb/s to 11 Gb/s

Ø Optical bandwidths to over 65 GHz for the most accurate waveform fidelity

Ø Most precise extinction ratio measurements

Ø Pattern Lock isolates bit sequences leading to mask violations and allows averaging to view noise-impaired signals

Ø Built-in equalization for analysis of dispersion limited signals and equalization verification

86100C DCA-J - Jitter Mode

The 86100C can perform accurate jitter analyzer measuring subcomponent jitter sources with one-button ease of use. Accurate jitter analysis, including decomposition of jitter into its constituent components, is becoming critical as data rates increase. Decomposition provides critical insight for jitter budgeting and performance optimization in device and systems designs. Jitter Mode decomposes jitter into its constituent components and presents jitter data in various insightful displays. Jitter Mode operates at all data rates the 86100C supports, removing the traditional data rate limitations from complex jitter analysis.

The Advanced Jitter Analysis - Option 200, provides:

Ø Decomposition of jitter into Total Jitter (TJ), Random Jitter (RJ), Deterministic Jitter (DJ), Periodic Jitter (PJ), Data Dependent Jitter (DDJ), Duty Cycle Distortion (DCD), and Jitter induced by Intersymbol Interference (ISI)

Ø Various graphical and tabular displays of jitter data

Ø Export of jitter data to convenient delimited text format

Ø Save/Recall of jitter database

Ø Jitter frequency spectrum

Ø Isolation and analysis of Sub-Rate Jitter (SRJ), that is, periodic jitter that is at an integer sub-rate of the bitrate

Ø Bathtub curve display

Related Applications

Ø Fibre Channel

Ø PCI Express

Ø FBD

Ø SATA

Ø SAS